This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
JPe
About
- Username
- JPe
- Joined
- Visits
- 1,509
- Last Active
- Roles
- Member
Comments
-
see also https://forum.athom.com/discussion/3140/play-a-sonos-playlist-on-sonos#latest
-
@RonnO @jovink @0burner0 This complaint it is placed in Github: https://github.com/athombv/homey/issues/1798 please add your complaints there too, so it gets attention from @baskiers Maybe a @moderator should make an official Main discussion to…
-
alexkost said: hello could you explain how to connect own pult and homey together? if I connect pult - homey is lost connection if I connect Homey - pult is lost connection I can't to do together What is Pult? what do you want to co…
-
@Rocodamelshe Did try with delay's of 3 seconds in between, no difference. When, in the Sonos-App, both speakers are at "Stop", and I run this flow, the speaker in the "Woonkamer" plays only one title and then stops, in "Sonos-App Wachtrij" ther…
-
@Ilmaro did you try to select a speaker in another room? and if so, does this work for you? I have a speaker in the "Woonkamer" and a speaker in the "Slaapkamer" bud when I run a flow like yours and select the "Slaapkamer" speaker, always the "Woon…
-
Why don't you ask Athom to implement the qubino device, many qubino devices are already implemented or ask @TedTolboom
-
Alle z-wave componenten die op de netspanning aangesloten worden, zullen de z-wave signalen doorsturen, dat noemt men "meshnetwork", hiervan is op dit forum heel veel terug te vinden.
-
@Arie_Laxed The status of the virtual devices like Away and Holyday are always set to OFF when the Homey software is updatet. This morning also again, I was afraid my holiday was over, but I could convince Homey, it's not, by setting the virtual d…
-
sorry, it was not exactly an answer, but more a work around. the answer is probably because floating point values are used, then 2 + 1 is not always exactly 3 but maybe 0.30000000000004 (caused by rounding in calculations), but I'm not an expert…
-
Chanel Up / Chanel Down zou ook een optie kunnen zijn i.p.v. zo veel individuele
-
After Increment use a card "Execute MathJs Expresion" with round(WAARDE * 10) / 10 , will give you 1 dicimal always
-
Why don't you try to make these examples in flows, then homey gives the answer, you also can send the results to a SimpleLog, so you can study the results afterward. ZoDus
-
Thanks @Nattelip after a PTP for >10 minutes and restarting Homey, every thing works again perfectly.
-
@Nattelip Hi, Is there a problem with this X10 App on Homey Firmware Versie: 1.5.0-rc.6, my devices aren't switched anymore since today, while Homey Firmware Versie: 1.5.0-rc.6 was installed last night.
-
@mixuk try to remove the device in: Settings / Z-Wave / Remove a device
-
How about https://apps.athom.com/app/com.swttt.homeydash ?
-
For me, qubino is also very interesting https://www.robbshop.nl/qubino-module-set, dimmers are easier to build in, in the ceiling because of no need for potential free input-contact.
-
Emile said: We're currently researching if we can make the USB port so that through a special cable you can use an external ethernet adapter. Just don't count on it just yet! Emile mentioned 2 links to devices, did someone do tests with t…
-
As far as I have found in the Homey documentation, only ASK modulation is possible, this means FSK is not possible. This sounds logical because a receiver cannot receive both types of modulation at the same time, and since Homey has to listen to all…
-
https://www.fibaro.com/en/compatibility/
-
@PimBliek you mean this one? https://apps.athom.com/app/com.horstmann
-
@bvb Did you already reset your Homey, by PTP (pull the plug, wait for 10 minutes, replace the plug and wait 3 minutes until Homey is started Up) probably all works well then.
-
As @MrDutchfighter says, what you want is already possible, you also can use Virtual devices placed in the "Devices Home Zone" for this, they are directly visible in the App and they can start/stop a scene with multiple lights and /or devices with o…
-
Game was played in Enschede, the Birthplace of Homey
-
that is what I try to say in my comment "you need the trigger from the moving", sorry being unclear
-
https://apps.athom.com/app/com.arjankranenburg.virtual
-
you need the trigger from the moving and the "Helderheid" copy from the Tags-puldown.
-
dennis91 said: I don't think there is something like that for iOS Maybe an "I'm going to sleep" button in the app would be nice? you can make a virtual button for that, if you place it like this, you will see it in the app at fi…
-
@nklerk no problem for me, already glad that I see "real" seconds now, I was experimenting with a speaking clock, using the card "Every Hour" and I see that the "TAG" time is mostly 30 seconds or more behind the trigger. Good luck searching, maybe…
-
@Bantje After installing Homey 1.5.0-rc2 I do have problems, the "Sonos related" flows are not working anymore