This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Fire69
About
- Username
- Fire69
- Joined
- -
- Visits
- 3,304
- Last Active
- Roles
- Member
Comments
-
What's the trigger for this in Dutch?
-
You need to use the entire url with the id included (the url you see at the webhooks main page)
-
You need to set the webhook in your Couchpotato installation also. In Settings - Notifications, enable Webhook and enter the webhook url.
-
@ErikVanDongen: Just upgraded to latest version. When I looked at the log it was empty, I confirmed my account settings and then the logging started again. Is this necessary after an update, or should I just be a bit more patient and will it start…
-
Working very good Going to test some more tomorrow, had to do a full reset of my Homey today
-
thuijbers said: ... when I manually turn the devices off. What exactly do you mean by that?
-
Don't get too optimistic...
-
Well, my Homey 'died' on me today... It crashed or something this morning, I could ping it but that's it. After unplugging and plugging it back in, got a red ring So I tried a reset without erasing data, could do the setup but after that it kept tur…
-
Or use some air freshener
-
Or i'd have to make a flow 'increase volume' that increases the volume by for example 5 and consists of: when > then 5 cards Maybe you can come up with a more practical solution?
-
jorden said: I could look into that, shouldn't be too hard, although I don't know how well Homey understands spoken numbers. Does it show them as numbers, for example 16, or as words, for example sixteen? (Not that that really matters, since I…
-
Would it be possible to integrate some voice commands in the app? Set volume to 'xx' for example? I switch my input with the Harmony app, would be great if volume could be done with your app
-
http://www.wikihow.com/Check-if-a-Remote-Control-is-Transmitting-an-Infrared-Signal No need for Marmitek/Harmony/flows...
-
MarcoF said: @Fire69; For now I decided to not upgrade/switch to Experimental. https://forum.athom.com/discussion/comment/19426/#Comment_19426 Couldn't control yourself any longer?
-
superice said: Yes, I think you are right. Thanks for your input! No problem, we have to thank you for your hard work on this!
-
DennisBloembergen said: Thanks for the comment! The strange thing is that i don't have anything installed. But i will look up the speech input! Thanks! Sure you don't have the Soundcloud-app installed?
-
MarcoF said: @Fire69; GC problems * Now: 0.966796875,1.0107421875,1.03173828125 What's GC? Actually, those loads aren't all that high. I averaged at about 1.5-1.8 all the time
-
MarcoF said: Here a pic of the meter running Homey(0.8.29, with high Top values) for about 7 hours "idle"; Are you going to upgrade to .30? Power consumption should go down a little thanks to the lower load I suppose...
-
BasVanDenBosch said: This also means Homey can run for a couple of hours on some batteries as a UPS... https://forum.athom.com/discussion/comment/11034/#Comment_11034
-
RobinVanKekem said: Fire69 said: superice said: I'd have to look it up, but I think the 1.x branch uses the language of the phone, 2.x has no localization yet, so english only. Would you prefer localization by phone or by Homey?…
-
Bumblez said: rob_houweling said: I know. And I am not doing much with homey yet. Just a couple of hue lights, 433 sockets and a couple of danfoss thermostats which I have not used in any flows yet. Just checked, I have 13 flows and …
-
rob_houweling said: I have the same issue, also on 0.8.30. Avg load is 1.80419921875,1.4267578125,1.29052734375 That's very high for .30...
-
Emile said: Hm, what's your average load @Fire69? Don't think that's the problem... [0.46044921875,0.54248046875,0.6416015625] As I said above, it only happens when it's been a while since it has spoken. I can make it read out entire …
-
It reports the temperature only if you have a device that can measure temperature In my situation, it uses the temp from my Fibaro motion sensor. " The temperature is 22.6 degrees"
-
Emile said: This should not happen on v0.8.30 or higher. Unfortunately, it does happen on .30
-
Great! Hope you have some fun with it!
-
Temperature/Temperatuur is a built-in command. If you just say 'ok homey, temperature', it will tell you the temperature....
-
posthok said: Ik hoop niet dat je het zo bedoelt. Nee, het is niet 'we kunnen je niet helpen', het is 'we willen je niet helpen' Lol, just kidding Je wordt op Tweakers net zo goed geholpen als hier. Daar is het trouwens net omgekee…
-
Same here. It's usually only the first time when it has to say something. After being silent for some time, the problem occurs again...
-
novaflash said: AntonMadness said: "I've got a homey and I want to paint it blaahaack!" ¿ Lol, before your time maybe. No Rolling Stones fan?